Saturday, July 30, 2011

New way of folding your Dahon bike!

Just discovered a new way of folding the Dahon bike today. The usual way of folding is to put down the seatpost, fold the handlepost down and then fold the frame in half. However, sometimes the problem or inconvenience comes when you are trying to fit the handlepost/handlebar in between the bike frame. You will need to rotate the handlebar or adjust the height of the handlepost in order to fit it between the wheels. This method applies only to inward folding handleposts, which basically excludes the high end bikes, where the handlepost folds outwards.

However, there is an alternative way of folding! Check out the pictures below

Step 1: Put down your seatpost, and turn your saddle as shown in the picture above. Seatpost should not be down all the way, or it might affect the later steps.

Step 2: Left crank should be rotated to approximately the angle shown in the picture above. Put up the kickstand.

Step 3: Fold the frame in half, don't close the magnetic latch yet. Rest the bike on its 2 wheels and seatpost.

Step 4: Fold down the handlepost, so that it goes over your rear wheel. The handlebar will go under your saddle/saddle bag. This is the tricky part, where you might need to experiment a bit to fit everything nicely. If the handlebar is stuck, it may be because the seatpost was put too low, causing the saddle bag to block the handlebar. When done properly, the handlepost will rest nicely on the frame and the magnetic latch can be closed.

Note that the left pedal will be in front of your front wheel as shown above.

The right pedal will be below the handlebar. All the vulnerable parts of the bike (Eg. Rear derailleur, brake levers, chainring etc) are now on the same side of the folded bike.

In this configuration, the bike can still be laid on its side, such as in a car boot, or stored standing up, such as in a hatchback car. It can also be carried onto the MRT easily, without fiddling with the handlepost height or handlebar clamp. The advantage is that the height of the handlepost does not need to be readjusted everytime you fold and unfold the bike. You can also place more accessories on the handlebar without affecting the folding. However, the folding package is now wider as the handlepost/handlebar now sticks out on the side.

2010 MuSL, with the RD on one side and the handlebar on the other side when folded.

This is somewhat better than the outward folding handleposts (where the RD is on one side and the handlebar is on the other side), as the vulnerable parts are all on the same side, allowing you to carry/lay down the bike on the other side.

In my case, this allows me to fold my bike for transport without moving the gold stem clamp that connects the handlepost to the handlebar. Try the method!

11 comments:

  1. interesting discovery! i shall try it on my Ventura and see if can be done too.

    ReplyDelete
  2. I did this by accident yesterday, whilst picking up my new Mu P8

    ReplyDelete
  3. Currently when the handlepost is folded, it rest on the left side of the bike.
    How about loosening the handlepost and and make it twist to the opposite side when folded, i.e. to the right side?
    Doable?

    ReplyDelete
    Replies
    1. It is possible, but not practical as you will need tools to loosen the handlepost, and afterwards you will need to realign it with your front wheel and tighten again. Too troublesome and takes too much time.

      Delete
  4. I have a Dahon Dream. I tried to fold like that but the handlepost (stock) hits the middle of the saddle

    ReplyDelete
    Replies
    1. If you turn the saddle, it should not block the handlepost.

      Delete
  5. I have a Dahon Dream. I tried to fold like that but the handlepost (stock) hits the middle of the saddle

    ReplyDelete
    Replies
    1. You may need to lower your seatpost or remove the seatpost before folding the handlepost. After that, you can reinstall the seatpost.

      Delete
  6. This is pretty cool. I'll have to try this out when my Mu P8 comes in. Just to be sure, does this mean you can possibly roll the bike while it's folded? I know you can't with the handlebars in the way, but when they're outside...

    ReplyDelete
    Replies
    1. It can be rolled, but it is still not that easy as it is not balanced.

      Delete

Every comment is moderated before publishing due to spam bots. If you don't see your comment yet, it is likely that it is currently being reviewed. Thank you for your patience!