Tuesday, November 5, 2013

Avanti Inc 3: Eccentric BB for Belt Tension Adjustment

While doing some upgrades for the Avanti Inc 3, I realised that the bike is quite different from any other bike that I have previously tinkered with. The most special part of this Avanti bike is no doubt the belt drive system.

A belt drive system is somewhat like a single speed bike, whereby there is no rear derailleur or front derailleur. To get more speeds on a belt drive bike, the only way is to use an internal hub. Some possible hubs that can be used would be the SRAM Automatix 2 speed hub, Sturmey Archer or Shimano 3 speed hubs, Shimano Nexus 5/7/8 speeds hubs, Shimano Alfine 8/11 speed hubs and the Rohloff 14 speed internal hub. These are some of the most commonly used internal hubs.

However, unlike a chain, the Gates belt drive system for bikes cannot use a chain/belt tensioner to apply tension on the belt. This means that the belt tension has to be adjusted by changing the distance between the bottom bracket and the rear axle.

The more common method would be to use horizontal dropouts, such as on most single speed bikes. A horizontal dropout would allow a pretty generous range of adjustment, and is probably the cheapest way of adjusting belt or chain tension. However, the downside is that once the wheel is removed, it is difficult to set it back to the correct belt tension, which is bad because belts are sensitive to belt tension. Brakes will also need to be adjusted if the wheel position is shifted, to ensure that the brake pads are still touching the rims properly.

To avoid these problems, well designed belt drive bikes use an eccentric bottom bracket for belt tensioning. An eccentric BB is basically an adaptor that goes in the frame, and the actual bottom bracket is then fixed onto this eccentric BB. As the BB is not centralised in the eccentric BB, the rear-axle-to-BB distance (or chainstay length) can be adjusted by rotating the eccentric BB in the frame. This allows the rear dropout to be of the vertical type, which ensures that the rear wheel always sits in the same position in the frame. Not only does this ensure that the brake pad alignment with respect to the rims / rotor does not change, it also makes rear wheel removal and installation much easier as there is no need to adjust belt tension repeatedly.

Default eccentric BB position. The BB centre is almost at the lowest position, which means that there is an equal range of adjustment forward (increase tension) or backward (decrease tension).

The belt tension that was the stock bike seemed about right. To actually measure and adjust the belt tension accurately, Gates recommend using one of their belt tensioning devices or iPhone apps. I have read that these devices are not really accurate, unless you get the high end devices which are really expensive. In the end I gauged the belt tension just based on my gut feeling, which is totally unscientific!

Anyway, after reinstalling the rear wheel, having changed out the tires to Schwalbe Marathon Supremes, the belt tension seemed to be lower. No idea why, as the BB position has not been adjusted. The bike was still creaking, and I have already ruled out the crankset, the BB and the pedals.

Due to the slack belt tension, I decided to try to adjust the eccentric BB to increase the belt tension. The eccentric BB looked simple enough, it seems that just by loosening the bolt, the eccentric BB will be free to rotate. I will also be able to grease the eccentric BB as that has been known to be a source of creaking.

 Eccentric BB with bolt for loosening or tightening it onto the frame.

After loosening the bolt, the eccentric BB was still stuck really tight in the frame. No amount of knocking around the adaptor could make it budge in the frame. Although there are holes along the eccentric BB, the pin spanner that I had could not hook onto the holes properly, and it could not be used.

 Pin spanner. Distance between pins are such that it does not fit into any 2 holes on the eccentric BB.

I tried using the Hollowtech BB tool to rotate the eccentric BB, by using the tool around the installed BB cups. However, I only succeeded in loosening or tightening the BB, the eccentric BB itself did not move at all.

Lastly, I tried knocking the bolt itself, as it might dislodge the wedge inside and allow the eccentric BB to move. It actually worked! By hammering the bolt (gently), the wedge will be pushed to the other side, and this actually frees up the eccentric BB. If only this was provided in a manual (if it ever came with a manual!).

Upon loosening the eccentric BB, I thought that it would be a good idea to remove the entire eccentric BB, and then apply some grease to prevent creaking.

Construction of the eccentric BB. By tightening the bolt, the wedge is drawn closer to the centre of the eccentric BB, and this tends to expand the outer diameter of the eccentric BB. This will tighten the eccentric BB against the inside of the frame.

Once again, pardon me for the lack of pictures as my hands were greasy most of the time. After I greased everything, I reinstalled everything, including the crankset, and went for a test ride.

Unfortunately the creaking sound was still present, and I have now narrowed it down to the rear hub area. The creaking sound is very regular, and is heard only during pedaling, and not coasting. It was possible that the interface between the rear sprocket and the Alfine hub is causing the creaking sound, thus I took out the rear wheel again, and removed the rear sprocket.

The retaining ring was really difficult to remove and install, as it was the flat type specially made for Gates belt drive sprockets. I greased all the contact surfaces between the sprocket and the splines on the rear hub, and reinstalled everything. By this time I think you can see how many times I have installed and removed the rear wheel and the crankset.

To my frustration, the creaking sound was still present. This meant that there was a possibility that the creaking sound could come from the Alfine 11 hub itself.

Creaking sound on the Avanti Inc 3 drivetrain.

At this point, I had already greased every conceivable part that could make noise, from the BB, crankset to the rear sprocket. However, the creaking sound was still there. It came from the rear hub area, and seemed to be from the internal hub itself.

As a last resort, I decided to adjust the belt tension to see if it makes a difference. Once again, this means removing the left crankarm, knocking the bolt on the eccentric BB, and adjusting the belt tension again. Finally, I found the cause for all the creaking!

The creaking sound was caused by the high tension of the belt acting on the internal hub. Although the tension is not high when I feel it by hand, it is too high for the rear hub to bear constantly. When I reduced the belt tension and turned the cranks, the creaking sound went away. It came back when the belt tension was increased. Finally, what I did was to adjust the belt tension a little bit, and turn the cranks to see if there was any creaking sound. Bit by bit I increased the tension, till the creaking sound came back. From there, I reduced the belt tension slightly, so that I get the highest belt tension possible WITHOUT causing that annoying creaking sound.

The final belt tension was quite a bit lower than I thought, but you don't feel any lag or stretch while riding. The belt also does not skip even when pedaling hard, so I guess the belt tension is sufficient.

All of that trouble, all because of the annoying creaking sound. As I have said at the beginning of this post, this Avanti belt drive bike is not a normal bike at all. It tends to be rather sensitive, especially for the belt drive system. A certain amount of hands on work and tinkering is required to get it running smoothly and silently. Although it takes quite a bit of work, the final result is really good!

The bike is now running so smoothly and quietly, and is a real joy to ride. Schwalbe Marathon Supremes are smooth and comfortable, although it can feel a bit narrow on certain patches of rough roads.

As for the gearing, I find myself using only Gears 1 to 8 so far. Have not had the chance to use gears 9,10 and 11, as they are too high for normal usage. Perhaps in the future I will lower the entire gear range, so that gears 9,10 and 11 can get used, and reserve the lower gears for climbing.

15 comments:

  1. Stumbled across your blog while researching EBBs for belt drive bikes. I'm in the process of getting a custom single speed cyclocross bike and I was considering the merits of going with an EBB rather than a slider or rocker dropout. Have you been satisfied with your EBB?

    ReplyDelete
    Replies
    1. The main advantage of eccentric bb over horizontal dropout is that chain tension can be maintained even when the wheel is removed and reinstalled. That should be useful when you remove the rear wheel to clean.

      Delete
  2. Top work! Agree with your diagnosis and have backed off the tension just a touch. Now running smooth and quiet. Seems the bike shops have been given instructions to set these things up with too much tension.

    ReplyDelete
  3. Great page, very helpful. I was just wondering how your Alfine 11 and belt drive is holding up?

    ReplyDelete
    Replies
    1. So far it working fine! After 300+ km it is still OK. Once the belt tension is adjusted properly there will not be any creaking sounds.

      Delete
  4. Hi, I've got an Inc 2 which I love...apart from a sound that I seem unable to localise. I think it might be the front disk brake but the sound only recurs under load when I'm pedalling. I've returned the bike to the Avanti dealer twice now to try to sort it out, and they've greased the BB and adjusted cables. If anything, the noise is now worse!!

    ReplyDelete
    Replies
    1. It might be from the rear internal hub. If the belt tension is too high, it can cause creaking sound when pedaling. Might need to reduce the belt tension slightly by adjusting the eccentric BB.

      Delete
    2. I have found creaking coming from the headset. So centre it only occurs when pedalling, I had focused my troubleshooting on the pedals/crank/BB/rear hub. My eureka moment occurred when I took my hands off the bars while pedalling and the creaking stopped. It disappeared temporarily after tightening the headset top cap but is back again and the headset preload feels firm as it is. Any more would be too much. Some further investigation is needed but at least I know where to focus my attention.

      Delete
  5. Thanks for the great blog. I've just purchased a Polygon Path i8 with Gates Carbon Drive and EBB. This is the first article I've found describing how to adjust belt tension with an EBB. The literature you get with a new bike is so vanilla and of little use.

    ReplyDelete
    Replies
    1. Gah, I've had my Polygon i8 since April 2016 and recently started to look at retro-fitting a single speed kit to tension the belt.
      Thankyou so much for commenting and saving my time and to Handsonbike for the blogpost.

      Delete
  6. This information "Lastly, I tried knocking the bolt itself, as it might dislodge the wedge inside and allow the eccentric BB to move. It actually worked! By hammering the bolt (gently), the wedge will be pushed to the other side, and this actually frees up the eccentric BB. If only this was provided in a manual (if it ever came with a manual!)." is absolute gold. Thank you.

    ReplyDelete
    Replies
    1. Fortunately this information is now in the YST manual for their ebb here:http://www.yst-corp.com.tw/download/BB2008-1C.pdf with pictures of said hanger included!

      Delete
  7. Today I adjusted my drive. The factory was so heavily stretched that it was a shame to talk. Thank you for your useful article.

    ReplyDelete
  8. You never did mention how to adjust the BB. After you get it knocked loose, what do you use to rotate the BB with? does it turn hard or easy and thus easily get too loose? I have this EBB with chain drive on my new Raleigh Tourist and couldn't figure out how to loosen a chain that's too tight. I guess I'll loosen that bolt, tap on it to disengage the wedge and just try turning it somehow (by hand?) to see what happens

    ReplyDelete
    Replies
    1. Use a pin spanner to engage the holes at the side of the eccentric bb, then rotate it.

      Delete

Every comment is moderated before publishing due to spam bots. If you don't see your comment yet, it is likely that it is currently being reviewed. Thank you for your patience!