Friday, June 12, 2015

Merida Scultura 5000: FSA K-Force Compact Road Handlebar

I am always on the lookout for good online deals, such as clearance sales from ChainReactionCycles or other online websites. Occasionally I do come across deals that are so good that it is better to buy first and think later. This new carbon handlebar is one of those purchases.

The stock handlebar on my Merida Scultura 5000 is a FSA compact aluminium drop bar, which is a good drop bar that I also use on my Dahon Boardwalk. I usually stick to aluminium drop bars, as I don't have to worry about handlebar damage if the bike falls over accidentally and hits the ground. I have been told that carbon handlebars should only be used if you can afford to replace it if damaged. This usually holds true as good carbon handlebars usually cost more than 300 dollars each.

However, with a good discount available, I decided to go for it, just to try out a carbon handlebar.

FSA K-Force Compact Road Handlebar, with its own special pouch packaging.

Overview of the handlebar

Centre clamp diameter of 31.8mm, 400mm width, 125mm drop and 80mm reach. Typical compact drop bar dimensions, same as the FSA aluminium handlebar that I have.

Compact and shallow drop shape for easy and more comfortable access to the drop portion of the handlebar

Unidirectional carbon lay up design is used for this handlebar

Recessed groove under the handlebar for hiding the cables from the shifter

Extra rough surface at the centre clamp area for extra friction when clamped in the stem

Same rough surfaces at the bends, to allow the shifters to be tightened properly to the handlebar without slipping.

Very lightweight carbon handlebar, at only 204 grams!

Removed the shifters from the stock handlebar, and removed the handlebar from the stem.

The stock FSA Gossamer aluminium handlebar weighs 297 grams, almost 100 grams heavier than the new carbon handlebar

Comparing the compact aluminium handlebar with the new compact carbon handlebar

Similar shape at the drops

Similar handlebar dimensions too

The carbon handlebar has a groove under the handlebar for cables, while the aluminium version does not

A flatter profile on the top of the carbon handlebar.

When installing bolts, especially on carbon products, it is important to use a torque wrench to prevent over-tightening of the bolts.

With the new carbon handlebar installed on the bike!

Close up view of the carbon handlebar and the carbon faceplate of the stock Merida/ControlTech stem.

With the original Ultegra shifters reinstalled onto the carbon handlebar. I did not have to disconnect any of the cables from the shifters.

Reusing the original bar tape! This bar tape is nicely designed and is also comfortable.

Reinstalling the K-Edge Aero Garmin & Camera combo mount onto this new carbon handlebar

The new carbon handlebar has been successfully installed and the bike is ready to go again!

With the weight savings from this carbon handlebar, this lowers the weight of the bike by a bit.

Upgraded bike inclusive of PD-A530 pedals: 7.7 kg
Upgraded bike with no pedals: 7.3 kg

As for the performance, I can't detect any difference in stiffness between this carbon handlebar and the original aluminium handlebar. Both the handlebars are already stiff enough for my usage. What I do like is the flatter surface on the top of the handlebar which is more comfortable for gripping.

In conclusion, the carbon handlebar is very similar performance-wise, when compared against the aluminium version. If weight savings is not a priority, the aluminium version is good enough, and saves you quite a bit of cash. However, if you want to save weight, and don't mind paying more, the carbon version would be what you are looking for.

11 comments:

  1. Well it's either you're too light to feel a difference or you don't ride the bike hard enough. There's definitely a difference in stiffness when you're out of the saddle and riding hard.

    ReplyDelete
    Replies
    1. Have you tried both the alu and carbon handlebars personally? I am just stating my personal opinion after usage, and not just repeating what the marketing material says.

      Delete
  2. Check out some of Time trial competition ( close up high resolution ) posted on Youtube in slow motion. ( You have to download movie to your computer and watch in super slow motion ). You can see the handle bar flexes like a spring.

    ReplyDelete
    Replies
    1. I definitely don't ride as strongly as those professional riders. Comparing the original aluminium handlebar to this new FSA handlebar, I can't feel much difference. This would be the case for most riders who are not professionals. Perhaps other handlebars are stiffer or more flexible, but comparing these exact 2 handlebars, this is the result of the comparison.

      Delete
  3. Recommend you to get red sticker line ( cover the blue line on you bike frame ) so that it would be perfect match for the new FSA carbon handlebar.

    ReplyDelete
  4. Any feedback on GIANT branded torque wrench ?
    Do you know any method to verify ( at home DIY ) the accuracy of torque calibration ?

    Thanks.

    ReplyDelete
    Replies
    1. The torque wrench works well, no issue with it. Just need to remember to reset the torque wrench to zero after using, so that the spring does not become deformed over time, causing inaccuracy.

      Not possible to calibrate a torque wrench at home without a proper calibrating jig or machine.

      Delete
  5. Big thanks to you for sharing such great information.

    ReplyDelete
  6. Hello there Steve.

    The FSA stock HB is 400mm or 420mm? And did you used carbon paste between bar and stem?

    ReplyDelete
    Replies
    1. Stock is 400mm. Carbon paste not required as there is a rough surface on the handlebar.

      Delete
  7. Sorry but you have missed the essential to me : the shapes ARE NOT the same at the drop between alloy and carbon handlebars: easier to put your hands down for the alloy one. I was very disappointed by both carbon SLK and K-Force for this point.

    ReplyDelete

Every comment is moderated before publishing due to spam bots. If you don't see your comment yet, it is likely that it is currently being reviewed. Thank you for your patience!