Wednesday, September 14, 2011

Journey of the Boardwalk: Part 13 - Dahon Boardwalk TT

Disclaimer: Major upgrade poison ahead! Read at your own risk!
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Ever looked at the Dahon Speed Pro TT, Vector X27 or the Verge X30 and wish you had the bullhorn handlebars? Now you can! With the correct components and some mechanic skills, you can install bullhorns on almost every Dahon folding bike. The bike will still be foldable, using the folding method described in an earlier post.

Advantages of bullhorn handlebars over standard flat bars:
1) More hand positions for better comfort and versatility, especially over longer rides.
2) Longer reach is possible, especially for people with longer upper bodies.
3) More aerodynamic when certain hand positions are used.
4) Brake and shift using the same levers, and reap the ergonomic benefits of the Shimano Total Integration (STI) levers.
5) More natural hand position (palms facing each other) when holding the sides of the bullhorn.

With all these in mind, I set about gathering the components that I needed for the upgrade. In fact it took me more than a month to gather all these parts. Needed to do some research and ask around too for advice. No hurry to do so since I can ride my bike in the meantime anyway.

Components required:
1) Shimano Tiagra 9 Speed STI Levers
2) Shimano 105 RD
3) Kinetix Pro TT bullhorn, clamp size 25.4mm
4) Inner cables and cable housings - LONG ones for the rear brake and rear derailleur
5) Travel Agents by Problem Solvers
6) Tektro Cyclocross brake levers
7) Lots of cable ferrules for covering the cable housing ends

The hardest component to find were the STI levers, it is difficult to find 9 speed ones nowadays. 105 and above level are all 10 speed already. Finally found a pair of second hand Tiagra levers from Togoparts after some time! Taken off a new bike so they are in great condition.


Previously I was using the SRAM X9 shifters with the X9 rear derailleur. Since I will be switching to Shimano STI levers, I will need a compatible Shimano RD. Once again Togoparts to the rescue! Second hand Shimano 105 RD, from the older 5600 series. No problem, black colour can already haha.

Most of the time, the STI levers are paired with caliper brakes, so that the cable pull when braking is compatible. However, I cannot mount caliper brakes on my Boardwalk, as there are no proper caliper brake mounts and also because the caliper brakes will intefere with the fenders. Caliper brakes are possible! Check out the next part of the series here.

In order to overcome this incompatible cable pull issue, I got these Travel Agents from a company called Problem Solvers. What these things do is to alter the pull ratio of the cable, such that the STI levers pull enough brake cable to activate the V-brakes properly. Without them, the V-brakes will feel very spongy and the brake pads will need to be very close to the rims.

To further complicate the upgrade, I decided to add cyclocross brake levers! (No challenge if the upgrade is too simple! LOL) These brake levers are mounted near the middle of the handlebars, and goes between the main STI levers and the brake calipers. They allow braking even when holding the middle of the bullhorns.

First step is to remove all the components on the handlebar, so that I can swap the handlebar! Not easy because I will also need to loosen all the cables and pull out all the cable housings. I cannot reuse the cable housings or cables because they will be too short to route the cables on the bullhorn handlebars.


After this, I needed to open up the chain so that I can remove the current X9 RD. On the SRAM chain that I am using, there is a Powerlink that can be opened up by hand. However, I found it difficult to open by hand most of the time, because it is quite tight and also because I have to work against the chain tension.

Got the KMC Missing Link Chain Pliers and a X-Tools Chain Connector Aid from CRC.

Hook the 2 ends of the chain connector aid around 2 chain links, such that there is no chain tension across the Powerlink. Squeeze the side plates of the Powerlink together (not shown), and use the pliers to push the 2 ends of the Powerlink together.

With the chain pliers, it is very easy to open the Powerlink! Also, the chain connector aid helps to remove the chain tension before opening the link, and holds the chain for you after opening the link! Simple but really useful tools, saves you from sore fingers and dirty hands.

Time to install the new components! See the new bullhorn, STI levers and Cyclocross brake levers! The gold coloured stem is no longer required to extend the reach.

Running the brake cable housing out from the STI levers is not easy, as the cable housing needs to come out at an angle, and then turn sharply to run along the handlebar. This causes more friction for the inner cable. A short section of housing is laid from the STI levers to the cyclocross brake levers, and then a longer housing all the way to the brake calipers. The inner brake cable runs all the way through everything to the brake calipers.

The inner brake cable first loops around the smaller circle, then around the larger circle. This results in the short pull of the STI levers being converted into a longer pull suitable for the V-brakes.

Setting up the shifter cable is much more straight forward, coming out the side of the STI levers and going to the RD.

Before I wrapped the bar tape, I went for a test ride around the neighbourhood, to finalise the positions and angles of the levers. This has to be done before the bar tape is wrapped, else adjustments would be almost impossible.

Wrapping the bar tape also takes quite a bit of skill. Not just anyhow wrap in any direction you like, you actually need to wrap it properly if you want it to last. Check out the youtube link here.

Note the interesting rotating bell on the left bar end, originally from Bike Friday!

Managed to fit my two front lights and cyclecomputer on the bullhorn!

So far have not had any problems with the bullhorn bars. Initially I was worried that the clamp in the middle might not be able to hold the bullhorn properly, allowing it to rotate if I placed weight on the handlebars. But it has been rock solid so far, no slippage at all.

Lastly, a picture to wrap up this wonderful upgrade!

Will be discussing the hand positions possible on the bullhorn handlebars in a future post. Stay connected and check back often!

Saturday, September 10, 2011

Journey of the Boardwalk: Part 12 - LitePro Pedals

Finally found some time to write about the LitePro pedals! Previously I was using the MKS FD-6 folding pedals, which are very good folding pedals indeed. The MKS pedals have very smooth bearings, which is why many cyclists with folding bikes have changed to the MKS folding pedals.

However, being folding pedals, the folding joint is ultimately the weak link in the whole pedal body. After using it for about one and a half years, there is some looseness when the pedal is unfolded. The outer half of the pedal will have some play relative to the inner part which is bolted to the crank.

Of course, there is no big deal, as the pedals still work fine. Another reason I changed pedals is because with the new folding method that I am using for my Boardwalk, I find that there is actually no need for folding pedals. The pedals will actually be kept within the folded package, even without folding the pedals.

Comparing the pedals, these LitePro ones are actually much lighter than the MKS pedals. According to my slightly inaccurate weighing scale, the MKS pedals weigh 440g a pair, while the LitePro pedals weigh only 220g a pair, half the weight!

New LitePro pedals!

MKS FD-6 folding pedals

Installation was not too difficult, it only requires Allen keys of the correct size and some muscle power. Some people have asked me why I didn't get the gold coloured LitePro pedals instead. Actually I had considered it, but a whole slab of gold would look out of place. Also, I wouldn't bear to step on the shiny gold pedals! Black would fit the cranks better and not dirty so easily.

These pedals are actually about 1 cm shorter than the MKS pedals. Initially I was not used to the smaller platform, especially when I was wearing my oversized Crocs haha. However, when I used my cycling shoes, the size was just right. As long as you don't have huge feet, these pedals would not seem too small.

Size of the pedal fits my shoe nicely!

Also, since there is no folding joint, the pedals feels much more solid when I pedal hard. Can feel a slight improvement in power transfer. Even though the bearings in the LitePro pedals are not as silky smooth as the MKS pedals, I can't really feel the difference when pedalling.

Besides the seat clamp and these pedals, some other LitePro products that I am using include the gold chainring bolts and the gold stem for the handlebar.

Gold chainring bolts on the crankset

Gold stem to extend the reach of the handlebar!

More info regarding the LitePro chainring bolts and stem can be found at the previous blog entries!

http://handsonbike.blogspot.com/2011/06/new-bashguard-for-my-boardwalk.html
http://handsonbike.blogspot.com/2011/05/journey-of-boardwalk-part-8-advanced.html

Sunday, September 4, 2011

Journey of the Boardwalk: Part 11 - LitePro Seat Clamp

My new LitePro components had arrived a few days ago, from Cyclopedia.com, the local LitePro distributor. However, I did not have the time to install them yet. Also, I did not want to put on new components for a tough ride like the King of Da Hills without some testing around the neighbourhood first.

Decided to change the seat clamp first, because I thought that it would take the least amount of time. Will be changing my seat clamp from the current silver seat clamp to the new gold coloured LitePro seat clamp!

My first impression of the seat clamp is that it is really well made. The edges are nicely finished with no burrs or sharp edges or scratch marks from machining. Brass shim between clamp and lever that does not deform when you clamp tight, unlike those with a rubber shim. Brilliant gold anodized finish, a quality product.

New gold coloured LitePro seat clamp!

There are two different sizes of seat tube clamps for Dahon bikes, 40mm and 41mm. This measurement refers to the outer seat tube size. For steel framed models, the size is 40mm, while the aluminium framed bikes use the 41mm clamp size. You can check the clamp size of your original seat clamp by looking at the bottom of the clamp. It should write 40 or 41mm, depending on your frame material.

40mm seat clamp for my Chromium-Molybdenum steel Boardwalk frame!

Adjusting nut of the clamp. It may look small, but is surprisingly easy to adjust!

Bye bye silver seat clamp.

First step is to remove the current seat clamp. This is actually harder than it seems, because the current seat clamp is probably stuck to the seat tube already! In a way it is good when in use, because it will not move about when the clamp is loose.

Tried to remove it by pulling apart the clamp and lifting it out.However, the clamp is quite strong and there is only so much that you can open it up by hand. To lift it out, you will need to open the clamp wider than the lip of the shim. It already takes two hands to open up the clamp, no more hands to pull out the clamp! In any case, even with two hands it is difficult to open the clamp wide enough to clear the shim lip. Fiddled around with it for quite a while without success, before I had an ingenious idea!

Ingenious idea: Find two M5 sized nuts, and screw them onto the seat clamp lever bolt as shown above. It should be a tight fit between the gap. Of course, the clamp would still be stuck on the seat tube at this point in time.

Next, take a size 8 hex wrench and turn the two nuts so that they move apart! By doing so, you will force the clamp open with ease. And the clamp will stay open thanks to the nuts. Do not overdo it, just open it to the extent that the clamp can fit past the shim lip, and then lift out the seat clamp.

The bare seat tube! Note the lip of the shim, which will come in useful if you want to lift out the shim.

At this point, you can just put on the new seat clamp and the seat clamp change would be done. I decided to go a step further and remove the shim, just for fun!

As expected, the shim is also stuck within the seat post. I tried using pliers to pull out the shim, but it was stuck fast. Hardly any grip or leverage on the tiny shim lip. And then I had ingenious idea number 2!

With the nuts on the seat clamp lever bolt still apart, flip the clamp upside down and put it around and under the shim lip. There is also a lip on the clamp. Then, turn the nuts so that they come together and the clamp closes up. The clamp lip will tighten around the shim, and you can just pull them out easily! Without the clamp, it would be difficult to get any grip on the shim.

Ta-da! Note the rust, which is from the steel frame, and not the shim itself as the shim is aluminium.

Rusty inside of seat tube! Still not too bad though. Must be from those wet rides where rainwater got in.

Cleaned the seat tube and shim, and then put on the clamp. It is easier to put on the clamp first, because without the clamp, it is difficult to judge how far in to insert the shim.

New gold-coloured seat clamp! The clamp lever is on the other side because of the wording on the clamp lever.

Insert the shim back into the seat tube. The lip of the shim will rest nicely on the clamp.

Last step, put back the seatpost and everything is completed! Took me almost an hour for the job, as I could not remove the seat clamp and shim, before I had the two ideas. With the tips above, it should take you much lesser time to change the seat clamp yourself.

The gold LitePro seat clamp! Compare it with the original one shown below.


Still have some more LitePro components, but will need to find more time to install them! Just as a teaser...

Wednesday, August 31, 2011

New Topeak Accessories!

Bought some new accessories for my bike!

1) Topeak iPhone Dry Bag

This was originally bought for another iPhone, but I found it so good that I went out to get another one for my HTC Desire! Of course, I tried the sizing before buying it for my HTC phone. Some of the advantages over some other iPhone mounts is that it is waterproof, courtesy of a double folded opening and ultrasonic welded seams. Although I wouldn't try dunking it in water, it should keep the rain out with no problem. Also, there is no need to remove the protective casing to fit the phone into the pouch.

The Topeak QuickClick system also makes it very convenient to remove the pouch and bring it with me when needed. If you have more than one bike, you can just buy additional mounts and switch the pouch among the bikes. Note the additional blue strap which I added, that serves as a safety belt for the phone pouch in case it decides to jump off the bike!

More details at the link below! If you want to try the sizing for your phone, look for me during the rides!

Topeak iPhone Dry Bag

2) Topeak CageMount

I got this because it enables me to separate the mount from the bottle cage when not in use. This is to allow folding when the second bottle cage is not required. This mount is also much more secure than the clamp on + quick release type.

From the picture on the website, Topeak CageMount, you can see that the mount splits into two parts, one part is fixed to the bike while the other is fixed to the bottle cage. By removing a bolt from the side, the 2 parts can be separated easily.

The part that stays on the bike when the bottle cage is removed.

I have since modified the bolt to be tool-free, by adding a wing nut so that I can install/remove the bolt by hand.

Just turn the wing nut instead of using an allen wrench to turn the bolt.

Both the phone pouch and bottle cage fits on the handlepost without interfering with each other.

Monday, August 29, 2011

Preparing the bike for King of Da Hill !

This coming weekend, we will be conquering all the hills at the southern and western part of Singapore! Some of the hills include Mount Faber, Bukit Chandu, Kent Ridge Park etc. I have not been to any of these hills before, so it will be an interesting trip for me!

Can't say that I have been training much for this, nor can I say that I am well prepared. But no matter what, I'm just going to have fun! I have heard that it is very difficult to get up some of the hills on a 53T Front/28T Rear combo, with a 20" wheel bike. Not good news for me, because that is the exact same lowest gear ratio that I have!

Some of the KODH participants have a double chainring up front, which makes it much easier to cycle up the hills with the lower gear ratios. However, for those of us who only has a single chainring up front, there is a limit to how low the lowest gear can go, without affecting the top gear too much.

With my Dahon Boardwalk, I have 9 speeds, with a 53T chainring in front and the largest sprocket at the rear being 28T. To get a lower gear ratio, I will need to have a larger rear sprocket or a smaller front chainring.

Contemplated getting a front derailleur adaptor for the Boardwalk, so that I can fix a FD and add the 39T chainring up front, to give me a 2x9 gear system. However it is quite troublesome, since I will have to fix the adaptor, FD, front shifter, cable housing. Also, I can't see myself using the 39T chainring other than for KODH or for touring?

Another solution is to change the cassette to one with a larger sprocket, such as 32T. However, this is also not as straightforward as it seems. Because of the larger sprocket size, my short cage X9 RD will not be able to handle the 32T gear. Short of changing the RD, I also cannot use a different cassette.

Finally, I hit upon another solution, which is to change the current chainring size! From the current 53T chainring, I can change it to a 45T chainring, which lowers all my gear ratios by 15%. Although I lose the top end speed, I gain by having a lower gear ratio to use while climbing the hills. This is a temporary arrangement, all for the KODH challenge!

Brought out my new bike workstand from X-Tools which I bought about 2 weeks ago! Ordered it online at CRC, had it shipped over and it is still cheaper than buying locally, haha. It is of good quality too!

Being able to fold the workstand is very important, as I can put it in one corner and not have it take up space when not in use.

Sturdy large diameter tubing, adjustable height and angle.

Solidly built clamp head, with cleverly designed latching mechanisms and easy adjustments.

Lever with cam profile allows quick clamping and loosening of bike.

Ta-da! All set up and ready for use! It only takes 15 secs to set up the workstand!

Although the workstand has a rubber clamp area, I still prefer to use a separate old seatpost for clamping, instead of my black seatpost. With the workstand, it is now much much easier and comfortable to work on the bike, since the wheels and cranks can spin freely without the kickstand or the ground getting in the way.

Note the different seatpost that I use. Very sturdy and stable workstand!

45T chainring with bash guard. Lowers my gear ratios by 15% compared to the 53T chainring.

An issue which I overlooked was the fact that the chain length would not be correct, since the chainring is now smaller. In fact, at the smallest sprocket at the back, the chain actually becomes loose! Luckily I could still adjust the B-tension screw on the RD to take up the slack on the chain. That was not the original design intention of the B-tension screw, but it works, and it is only temporary so it is fine. Shifting is not as crisp because the guide pulley is now further away from the sprockets, but again it is fine because it is only temporary.

Will be testing out the new system very soon, hope it works well and comes in useful for KODH!